How Much HP Can A 350 Make?

How can I get more horsepower out of my 350?

No matter what application your Chevy 350 motor is in, a few simple steps can get you more better performance and higher horsepower.Modify your air intake.

Modify your exhaust.

Change your camshafts and valve train.

Purchase new cylinder heads, or have yours ported and polished.

Have your motor rebuilt and blueprinted..

Why is a 4 bolt main better?

Any time you increase horsepower, torque and cylinder pressure, you increase crankshaft load. It would take quite a bit more stress to rip-out 4 bolts than it would just 2, so that’s why the 4 bolt mains are stronger than the 2 bolt mains.

How much does it cost to turn a 350 into a 383 stroker?

Re: Building a 383 Stroker, costs and challenges You can put a 383 together to handle about 400-450 horses for probably $1500-$1600. That would be a short block. It’s probably possible to build it for around $1200 everything off a 400 and 350 except for new pistons, rings, and bearings.

How much HP does a 383 stroker make?

That combo would probably make around 465 hp and nearly 500 lb-ft, but at less rpm. But never mind that. The point here is 502 lb-ft at 4,700 rpm and 500-plus horsepower from 5,700-6,200 rpm….Hot Rod’s Proven Recipe For A Simple Chevy 383 That Knocks Down 500 HP And 500 LB-FT.True 383 PowerRPMLB-FTHP6,20042550222 more rows•Oct 13, 2009

Can you make a 2 bolt main into a 4 bolt main?

Registered. It’s not worth it to take a factory two bolt and turn it into a 4 bolt unless you know someone who owns a machine shop and can do the work for free. You can get a used four bolt block for way cheaper than the four bolt conversion parts and labor charges.

How much does it cost to rebuild a Chevy 350?

$600 to $3,500 depending upon how involved you want to get with the thing. Generally, for a “good” rebuild that doesn’t really get beyond ‘mild 350’ standards, you’re looking at about $1,600-2,500 depending upon location.

How much does it cost to build a 400hp 350?

The final bill for our 400hp build up checked in at $1,155, including the cost of the motor. We were excited about the 400hp peak number, but what really made us happy was the fact that this low-buck motor produced over 400 lb-ft of torque from 3,700-5,200 rpm.

How much HP can a 4 bolt main 350 handle?

1. 4-bolt blocks with OEM main bolts are good to 475 HP, and are good to 7200 RPM. 2.

How much horsepower can a Chevy 350 2 bolt main handle?

Stay away from the 2-piece rear main! A 2-bolt main with aftermarket studs is stronger than a 4-bolt main block, less prone to crack, and can take up to 600 HP on a seasoned block.

What year is the best Chevy 350 engine?

L31 (2002) From a purely technical standpoint, the most recent version of the Chevy 350 would naturally be the best of the bunch. Marketed as the “Vortec 5700” engine, but known internally by the moniker of L31, this engine was used primarily in GM vans and trucks until 2002.

How much does it cost to increase horsepower?

Horsepower gain varies depending on the brand of the intake and the engine it is bolted to. Typical gains are in the range of 5 to 20 horsepower. Cold air intake systems generally cost around $100 to $400 and there are a number of reputable manufacturers, including AEM and Injen, who carry a variety of models.

Why is a 327 better than a 350?

A 327 with it’s shorter stroke would need shorter gears so it can GET to its revs, where a 350, with its slightly longer stroke and more torque output will pull a little taller gear than the 327 will.

How much power can a 2 bolt main 454 handle?

Horsepower Enthusiast The 2 bolt Big Block Chevy blocks are fine for anything up to 6500 RPM and 600 HP.

It’s one of the most reliable engines ever Even if you drive in tough conditions, the Chevy 350 remains very dependable and keeps running. It’s been around since 1967, and Chevy was making small-block engines long before then. Everything about the Chevy 350 stands the test of time.

Can you get 500hp out of a 350?

You “can” get 500HP out of a 350 BUT because it is a small cubic inch engine it IS going to be peaky and won’t have much torque. … You do NOT want a “chain saw” of an engine in your car! Chain saws make NO torque and they only way they can cut wood is at wide open throttle at their peak RPM.

Why did Chevy stop making the 350?

GM made extensive use of the 350 across its lineup until 2004, when it was discontinued in favor of more modern and fuel-efficient engines. Chevrolet first produced the small block V8 in 1955 as a 256 cubic inch (4.3-liter) engine.

How much HP can a Chevy 350 handle?

a typical 350 Chevy can make upwards of 350 – 375 HP before you exceed the reliability of the components. For a big block with the same stock components it can make in the area of about 400 to 475 or so HP and handle upwards of about 500 HP before you exceed the reliability of the stock cast pistons.

What is the cheapest way to increase horsepower?

5 Cheap Ways to Increase Horsepower (Under £400) Posted by Amsoil, 12th January 2018More horsepower! … Upgrade your car’s air intake. … Upgrade the car’s exhaust. … Engine tuning & performance chips. … Install a boost controller. … Upgrade to synthetic engine oil.

How much HP does a cold air intake add?

It makes such a big difference, in fact, that the simple process of redirecting the filter to draw cooler air is good for a horsepower gain of about 5 to 20 ponies in most cars. It might even improve your fuel efficiency, and it’ll probably make your engine sound better, too.

What is the easiest way to increase horsepower?

Here are some popular methods to increase your engine’s horsepower.Cold Air Intake. Upgrading your vehicle’s intake is one of the easier methods for unlocking some extra horsepower. … Performance Exhaust. … Software. … Forced Induction. … Performance Engine Build. … Engine Conversion.

What is the difference between a 2 bolt and a 4 bolt 350?

Two bolt means each main cap uses two bolts to hold it down. Four bolt means there are four, which means more clamping force, and less likelyhood that the crank is going to push itself out of the bottom of the engine at high RPM / power. Here is the “splayed” 4-bolt mains. These are always aftermarket.

Can a stock 350 handle a supercharger?

Installing a supercharger on a stock engine generally works well as long as the static compression ratio is 9:1 or less and engine speed is limited to 6,000 rpm.

How many miles will a 350 Chevy last?

229k miles is not unheard of for a properly maintained 350. You could do a compression test and leak down test to analyze the health of the motor.